Devex Electric Floor Heating

  • Xmat™ MG-150

    0 out of 5

    Thin Heating Mats (c/w Single Cold Tail)

    Devex Systems’ Xmat™ MG-150 electric floor heating mat is only 3.5mm thick and uses a twin conducting heating cable for ease of installation, with very low EMF. It can be easily installed directly over concrete, fibre cement sheet or F-board insulation and into thin adhe- sive beds or floor levelling compounds. This means there is minimal increase in the floor height. The system is best utilised on a “time of use” tariff as it is quick to come to the desired temperature. The X mat is 500mm wide and come with a single 3m cold tail. The cables comply with IEC60800:2009.

     

    We recommend the use of F-Board Insulation with electric floor heat- ing to improve warm up times and reduce running costs.

    • 20 year warranty
    • Output power based on 230 volts
    • Operating Temperature Range: -30°C to +80°C
    • Minimum Temperature during Installation: -5°C
    • Self adhesive mesh sticks to any clean substrate
  • Xcable™ CK-17

    0 out of 5

    In Screed Heating Cable (c/w Single Cold Tail)

    Devex Systems’ Xcable™ CK-17 electric floor heating cable uses a twin conducting heating cable for ease of installation. This flexible cable made with fluoro-polymer and durable PVC outer sheath can be easily installed directly on a structural slab, fibre cement sheet, or F-Board insulation and into 20-25mm screed bed. This system best operates on a “time of use” tariff as it is quick to come to the desired temperature. The X cable is rated at 17 watts per meter and comes with a 3m single cold tail. The cables comply with IEC60800:2009.

     

    We recommend the use of F-Board Insulation with electric floor heating to improve warm up times and reduce running costs.

    • 20 year warranty
    • Output power based on 230 volts
    • Maximum Operating Temperature: +70°C
  • Xcable™ CT-30

    0 out of 5

    In Slab Electric Heating Cable (c/w Single Cold Tail)

    Devex Systems’ Xcable™ CT-30 electric floor heating cable can be installed into concrete slab under a wide range of floor coverings. The CT-30 has a very low EMF and its single cold tail makes it easy to install. The CT-30 is most suited to be connected to an “Off-Peak” or “Time of Use” tariff as an in-slab storage heating system. This cable’s steel armor and multiple layers of conductor insulation make it extremely durable and also able to be used for snow melting. The cable is rated to 30 watts per meter and it comes with a single 3m cold tail.

     

    We recommend the use of Extruded Polystyrene (XPS) Insulation with electric in-slab heating to improve warm up times and reduce running costs.

    • 20 year warranty
    • Output power based on 230 volts
    • Maximum Operating Temperature: +70°C
  • Xthermostat™ TS-100

    0 out of 5

    Description

    • Electronic surface-mounted thermostat with setback mode.
    • Switch to select comfort, setback or external timer.
    • External timer to signal comfort or setback.
    • The ability to regulate either the floor temperature, room temperature, or a combination of both.
    • ON /OFF switch.
    • Relay 16A.
  • Xthermostat™ TS-200

    0 out of 5

    Description

    • Electronic semi-recessed thermostat specially designed to control electric floor heating.
    • Setback for night reduction (-4°C) via external timer.
    • Possibility to regulate either the floor temperature, room temperature or a combination of both
    • ON /OFF switch.
    • Relay 16A.
    • Can be mounted horizontally or vertically.
  • Xthermostat™ TS-300

    0 out of 5

    Description

    • Programmable semi-recessed thermostat for controlling heating systems.
    • Customisable 7 day timer programmable down to the minute.
    • Floor or room sensing
    • ON /OFF Main switch.
    • Relay 16A.
    • Can be mounted vertically or horizontally.